Friday, November 1, 2024
HomeTechnologyVictony AC1200 WIFI  Extender Setup

Victony AC1200 WIFI  Extender Setup

Insert the Victony extension into a power outlet to connect. To enable dual-band operation and 1200Mbps throughput, a few simple procedures are necessary.

The Victony AC1200 WIFI extender Setup is simple. Because it is a plug-and-play device, it connects to any network in 20 seconds. The Victony AC1200 wifi extender configuration lets you choose between router, repeater, and access point modes, depending on your needs. Keep in mind that altering the mode necessitates the reset or modification of the Victony Extender.

Setup Process | Victony AC1200 Extender

 

To configure your Victony AC1200 Extender, follow the procedure below:

  • Install your router and the Victony WIFI extension in the same room first.
  • Check that the extension receives at least 50% of the signals from your router.
  • Switch on your router and the extender.
  • Check to see whether the LED light has turned green after a few seconds.
  • Connect to the Victony ac1200 extender setup after accessing the wifi settings on your laptop, desktop, or mobile device.
  • There is no need to enter a password the first time because they will connect to your device immediately.
  • They exhibited no trace of internet access after joining but before starting any web browsers.
  • Enter the AP.setup command.
  • Enter setup or 192.168.10.1 in the top url bar to go to the login screen.
  • After you’ve finished configuring your extender, turn it off for 15 to 20 seconds before turning it back on.
  • To connect your device, utilise the Victony wifi range extender settings; the name in your wifi list is “SSID EXt.”

Note: If you continue to have problems with your Victony AC1200 wifi extender, please contact our professional. You may also visit our official website, ap setup.

If you want to install a wifi extender manually, follow the steps below:

  • The dead zone and router must be placed midway between the extender and router.
  • The extension should then receive at least 50% of your router’s signals.
  • By turning the extender mode switch, the Victony AC1200 extender should now be activated.
  • Hold the button down until the power LED turns green.
  • Then, on any of your devices, such as a phone, tablet, or laptop, go to the Wi-Fi settings and connect to the Victony wifi network name. It will resemble a Victory or WIFI-N extension.
  • It will first appear to be an open network, therefore you will need a password to join it.
  • The notification “No internet” will appear after the connection has been fully established.
  • Now, open the browser on your smartphone and enter 192.168.10.1. Fill with the username admin and password admin. lowercase only
  • Choose the network you wish to expand, name it, and then enter the password to confirm your choice.
  • After you’ve made all of the adjustments, you can reconnect your devices for a few seconds while the system reboots
  • Connect your devices to the Victony AC1200 repeater network (SSID EXT) as soon as it appears in your Wi-Fi list.

You have successfully finished the manual setup of your Victony AC1200 Extender.

Victony AC1200 extender setup via WPS

 

Press the WPS button to connect your WiFi range extender to the AP. To set up your new extender arrangement, follow the steps below:

  • Begin by connecting your extension and router using an Ethernet cable.
  • Wait for the LED light to stabilise.
  • Next, press and hold the WPS button for 5 seconds.
  • After 15 to 20 seconds, the lights on both devices will begin to flicker, signalling a successful connection.
  • Your new extender may now be placed wherever you choose using a range extender setup because it has been disconnected.
  • After inputting the same password for both your router and the new extender settings, you will see “SSID EXT” in your wifi list.

Now your  setup of Victony WIFI AC1200 using WPS method has successfully completed

How do i reset Victony Wifi AC1200 extender

 

  • Ensure the Victony extender is correctly connected to the power outlet before attempting to factory reset it.
  • Check the repeater’s  reset hole.
  • Furthermore, use a paper clip or pencil to hold the reset hole down for 20 seconds.
  • As you reset the wifi booster, the power led indicator will become amber.
  • Look for a steady green turn on the power lead.
  • For advice on how to reinstall the setup Victony WIFI extender, see the following section.

Note: if still you are facing any issue regarding AC1200 extender setup then please  contact us via live chat or New Extender setup.

admin
adminhttps://www.shoutonn.com
Elorabrown Blogger & Admin Shoutonn.com
RELATED ARTICLES

Most Popular

Recent Comments

Alex White on Gift Card